Sony bravia tv red light blinks 6 times

The diagnostic blinking will occur automatically with no action required by you to engage it. The timing of the blinking you see would be as follows: two to nine blinks, depending on the faultabout a third of a second apart, then a pause for 3 seconds, then the two to nine blinks about a third of a second apart again. Here is a list of the problems that might have occurred indicated by the number of blinks.

The words in parentheses are those, which you will see for each of these faults on a diagnosis screen described later in this article. Nine blinks - Replace D and D on the "G" board, do not resolder as this will fix the problem temporary. If it is intermittent 9 blinks, meaning sometimes the TV comes on and other times you get flashing, then change the switching regulator on the "G" board or check connections.

Make sure the regulator is or negitive. Ten blinks - Check Q and Q for shorts, leakage, or bad solder connections on the " D" board. If the transistors are bad, check R and IC, also on the "D" board. Intermittent problems? This is a great feature. You can also bring up these fault codes on-screen to see a list of the problem numbers with the abbreviation of the problem and the number of times this problem has occurred. This is slightly different than entering the service mode.

To see the diagnostic screen, press the following buttons: Display, Channel, 5, volume Minus, not plus then Power.

This brings up a screen with a list of the problems and number of times they have occurred. We have repeated them in parentheses in the text for the "Blinks" described above so you can correlate between the diagnostic screen and the blink codes. Now that you know about these self-diagnostics, how do you use them? Say that you have a set with a black screen.

You see that the LED is blinking four times. This would tell you that you have no vertical sweep, which is why the video is muted. If it was blinking 6 times, you would know that you have a horizontal fault. It's not a sure cure.

sony bravia tv red light blinks 6 times

These codes do not reset themselves after the fault is corrected, so if you don't clear them, you'll be seeing "old" fault codes the next time you enter this screen. Clearing is done by going into the service mode display, channel, 5, volume plus, then power. Press 8 and Enter, which returns everything to the factory preset condition.

I read that you have access to repair manuals for Sony TVs. I have a friend that has a Sony KPWS that quit working No picture, and it turns itself off 5 seconds after after turning on. Do you have an eloctronic version of the manual?

If so, would it be much trouble to e-mail it to me at garth yahoo. Any help would be appreciated. This forum has been helpful to me in deciding how to handle my Sony problem and also in guidance choosing its replacement. My Sony Vega is doing the blinking thing, It blinks like normal on statup but only has audio- then turns itself off. After that it gives me 10 blinks- with no audio and repeats 10 blinks over and over untill I turn it off.

I got it to work for me later in the day, picture and audio.I didn't even know that you could resolve these issues on your own. I've always thought that once a TV got damaged it was either broken beyond repair, or needed professional help. I guess that's okay with older TVs. It would be hard to accept that with the more expensive TVs we all have now though. I would definitely want to do whatever I could to fix, rather than replace my TV.

Hello, i have a problem with my Sony Bravia KDLW when i turn on the TV, the screen is black, after some time may be 2 minutes the tv turn off automatically and the red blink light 14 times. May you help me? What i need to do? Screen goes black after 10 seconds, or so. Then get the red standby LED that flashes 14 times, then repeats. TV is only 5 or 6 years old.

Did anyone find a resolution to the problem? Maybe try what suggested above in the article? Unplug the tcon board. When i unbox it and try to turn it on for the first time, it straight send me to a setup page. Before i can do anything, it turns off by itself, even i press the power button on remote or on the TV itself it just wont come up.

There is red blink light 6 times on the LED indicator. Please advise how to fix this, it's brand new, very sad. One of the 15 V DC output capacitor broken. Thank you for the efforts you made in writing this post.Last night I was getting picture but only for minutes after unpluging from main, also last night I connected to the internet and watched for about 30 minutes.

Sony Bravia TV kdl- red blinking led light error codes & solutions

Now no picture at all only the blinking light. I hope you can help. I have had a look at the service manual for your model tv, 3 blinks is indicates a DC Alert or audio and communications error. Unfortunately that is all I can find out im afraid. Community Share your experience! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for. Search instead for. Did you mean:. Join now - be part of our community! Sign In Register. Blinking red light 3 times. All forum topics Previous Topic Next Topic. October Best wishes salim nasra. Re: Blinking red light 3 times. If the stanby light is flashing red then it indicates that the TV's self diagnosis mode has been activated, I suggest you contact your local authorised Sony service centre and inform the them of the sequence that the Standby light flashes. This is only year old TV.

How much is expected to cost me to get sony centre to sort it out??. This is a poor quality product I paid premium price for it because as I always buy sony?

Thanks very much for your help, I think I will buy new one, it will be LG this time. Find a Store Find a Store Search. United Kingdom. View Pins. Follow us on Twitter.

Visit us on Twitter. Subscribe on YouTube. Visit us on YouTube. Like us on Facebook. Visit us on Facebook. Code of conduct.The standby light on a Sony television indicates when the television is turned on and operating, or turned off and in "standby" mode. However, this light also serves a secondary function: indicating when there is a problem with the television by flashing. When you see your Sony TV's standby light flashing, there are two reset options that can be performed to resolve whatever issue it's indicating — a power reset and a factory reset.

If a power reset, firmware update and factory reset fail to resolve the issue, contact Sony technical support so they can advise on options for repair.

A power reset is a soft reset that does not erase your TV's settings but can resolve some issues that cause your TV to not behave properly.

Understanding Sony Television Blinking Codes

A factory reset, on the other hand, completely resets your TV in a way that erases your personalized settings and calibrations. Sony warns that there is no way to recover these settings — you will have to re-enter them, just as you did when you first set up the television. To perform a power reset, first turn off your television and unplug it from the electrical outlet. If you're using a surge protector or power strip, disconnect the television from the strip itself. Only by disconnecting the power cord from the outlet can you ensure no power reaches the TV during the power cycle.

Leave the television without power for at least 60 seconds. This gives the television enough time for all components to power down during the power cycle. You can then plug the television back into the electrical outlet.

If you're using a surge protector or power strip, Sony warns you should plug the television directly into the wall outlet instead. The surge protector may otherwise interfere with the power-up cycle, especially if it is old or damaged.

sony bravia tv red light blinks 6 times

After you plug the TV back up, you can turn on the TV again. If you still see your Sony TV's standby light flashing, you can try updating the television's firmware since this can solve the issue without having to undo all your personalized settings. Otherwise, you'll need to do a factory reset. If you need to perform a factory reset, first turn on the television. Press and hold either the "Reset" or up arrow button on the remote control. Press and release the "Power" button on the front of the television, while keeping the "Reset" or up arrow button on the remote depressed.

Release the "Reset" or up arrow button. Allow the television to reset after the "Reset" message appears on the screen. Make no adjustments to the television for at least one minute after the reset has completed. This is to allow the television time to finish auto-configuration and initial set up.

After the reset completes, turn off the television and unplug the power cord from the electrical outlet. Wait ten seconds and then plug the television back into the electrical outlet and turn on the TV. Follow all on-screen instructions to complete setup.

These are the instructions displayed the first time you set up the television, for configuring channels, menu language, time, display properties and more.

By : Shea Laverty November 2, I bought a Sony XBR55XC brand new two years ago and unfortunately i am getting what i am seeing as a very common problem where the TV will not start up and just blinks a code of 4 red blinks.

I tried everything that is recommended to try but no luck. Looking online i seen many are experiencing or have experienced the same exact issue and not just on my model TV.

Most are saying it is a LED issue. Welcome and thank you for considering Sony Community! You may refer to the link below for possible troubleshooting steps to fix this issue:.

I tried all those things and still just get a 4 blink code. It will start the android screen but does not go further, it just it shuts down and blinks 4 times? Thanks for the reply. However, if the issue still occurs after trying the troubleshooting steps, the TV may need repair. You may refer to the link below to locate the nearest authorized service center in your area:. IF your TV still turns on and displays a picture brifly sony logo, android. I have created a PDF on how to do this:.

Now we get the 4 blinking lights. Waiting to hear back from Sony. Will your fix work on this model? I couldn't say for certain if it will work on your model. I certainly wouldnt attempt to open the TV until you have exhausted all possibility of having Sony repair it. If you are in the UK for example, you have a good chance of getting it repaired up to 6 years old.

Thank you, we tried everything Sony suggested. But will wait to hear back from them. We regret to hear about what happened with your television.

sony bravia tv red light blinks 6 times

We apologize for the delay in our response. What are our options? TV is only 14 months old, this is so unacceptable. Let me check your file. May we know your case number? We are in the same boat as Anitalioi. We bought our TV 14 months ago and now rather than turning on so we can watch the Raptors in their historic run to an NBA championship, it goes from one white flash and then the ominous 5 red flashes.Looked at many You Tube vids and all seem to indicate the main power or logic board.

Any ideas or are we looking at the main screen gone and its a throw away job? Thanks Warren. So a lady is selling me a mint condition 72 inch Sony TV with 6 red flashes with black screen for 40 dollars. Is it worth purchasing and try to repair? I have some experience in TV repairs so I'm not worried about that. What I'm worried is the parts gonna be to expensive. My one has 4 blinks I turn the tv off from the plugs, switch it on and then the android intro comes but then turns black and starts blinking again.

What should I do? One repair shop said bring it in and we will check it but they are almost 1. I think he is correct.

Phase #1 Sony KD-60X690E 6 Blink No Power

He has been doing this type of work for along time. So what do I replace it with? I am not a big fan of Samsung customer services. Perhaps LG this time. It seems that all current TV are just disposable. My Sony 46hx keeps getting stuck in standby, I get the 4 red standby blinks, after I turn it on. I've done the reset, and some times it fixes it, but not always. Sometimes it won't work for days. Yesterday I took the back off and looked inside, I discontented the inverter board, plugged it in and it started up with no picture.

Then I reconnected the inverter, and started it up, it worked perfectly. I don't know if it was just luck or if the inverter is faulty. I have read it could be the tcon or the power supply, any tips how to find the fault?

Any help would be greatly appreciated. I have a Sony xbr55xc I dont have video but I do have sound. When the TV is plugged in but not on the standby light on the bottom blinks green and orange. Your help will be appreciated. Sony xbr 49xc turns on shows sony logo then black screen.

I unplugged it and let it sit for 10 minutes, replug now it works. My TV is awesome, still quite old. It's big, it has that transparent bezel, and it weights 50 kg so repairing it is not easy.

I am happy the unplugging worked. Actually it happened before, and the restarting worked. Hey Same thing happened to me. I waited for a couple of hours and plugged it in again. Problem was the power surge coming into AC Socket. I have an old power stabilizer. I hooked my TV into that and it worked. Please try this before making costly decision. I hope it helps any of you reading this.I bought this TV about 2yrs ago. Now when you switch it on the sony logo comes on for a couple of seconds then goes off and the led on the front flashes red 6 times.

Just wondered if anyone had any ideas before i throw it away. Not impressed with the fact its failed so soon and wont be buying another Sony. Luckily i have a Samsung which ive had about 5yrs with no bother which iam using for now. Go to Solution. I would suggest you contact an authorised Sony Repair Centre in regards to getting this fixed. View solution in original post. Iam currently living in Australia but bought the set when i lived in the UK.

They dont have that model over here thats why iam trying the forum. In your opinion is it definately one of the boards?? If so is it worth me just taking a punt and trying to source them or am i best just junking the set?

Resolving The 6X Red Blinking Light Of Death On My Sony TV (with pictures)

Which btw wouldnt be another sony one if 2 yrs are their limit. The blinking lights, always indicates a hardware fault. The information I have is the A, B boards. Unfortunately, I cannot tell you if it is uneconomical to repair. I would say, you were unlucky on that one to be honest. Community Share your experience! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for.

Did you mean:. Join now - be part of our community! Sign In Register.


comments

Leave a Reply

Your email address will not be published. Required fields are marked *